Just How To Install A Bathtub (For Newbies).
Just How To Install A Bathtub (For Newbies).
Blog Article
What're your ideas about How to Install a Bathtub Yourself?
Installing a tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably challenging task. If the old tub is easily obtainable, the task can move immediately; if you have to open a wall surface to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old tub as well as embeded in the brand-new one. Make sure you have certified on your own for the job and are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed task, it is better to think about utilizing one prior to you start. Chances are you may need an expert plumber to make tube links.
This write-up will help you set up a brand-new bath tub in your washroom if you have already purchased a new tub as well as do not require to transform the setup of your previous water supply pipes.
Your tools and material checklist ought to make up the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome because of the limited gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. When the supply pipes have been removed, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning during this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Prior to carrying on to fit the new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical tap adapters. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Using both wood boards under its feet, put the bath tub in the needed placement. The wooden boards are handy in evenly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 tiny factors.
The next objective is to make certain that the tub is leveled all round. This can be attained by checking the level and also changing the feet on the bath tub until the spirit level reviews level.
To set up faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipe by making a compression join; after that do the same for the other faucet.
Activate the supply of water as well as examine all joints and new pipework for leakages and also tighten them if required. Fill up the bath tub and also inspect the overflow electrical outlet and the normal electrical outlet for leakages.
Ultimately, fix the bath paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bath tub needs to wait until the bathtub has been utilized at the very least once as this will settle it into its last placement.
Planning for the Installation
Firstly, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last setting.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to crack an inflexible seal, triggering the water to permeate the wall in between the bath and the tiling, leading to difficulties with moisture as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can break rather early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the marketplace. It is a good idea to fit the tiles making use of waterproof or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that blog entry on Tools You Need to Install a New Bathtub when doing a lookup on the web. Sharing is good. Helping others is fun. Thank you so much for taking the time to read it.
Order Repair Report this page